1) Ukuqina kunye ne-LOST motion

Ingqungquthela ye-hysteresis ibonisa ubudlelwane phakathi komthwalo kunye nokufuduka (i-screw angle) ye-shaft-speed shaft ukusuka kwi-shaft-speed side ukuya kwi-torque elinganisiweyo kwaye umthwalo usetyenziswa ngokukhawuleza ukulawula i-shaft-speed shaft.
Eli jiko le-hysterisis lihlulwe libe ngamacandelo amabini: ukugqwesa malunga ne-100% ye-torque elinganisiweyo kunye nokuphazamiseka malunga ne-0%.

  Ntwasahlobo rhoqo...
ULAHLEKILEYO ···· Iengile yomsonto kwi ±3% yetorque ekalisiweyo

Uluhlu 1 Amaxabiso okusebenza

Uhlobo lweNombolo ye-torque
1750rpm
(kgf)KULAHLEKILEYO IINTSHULULO zentwasa hlobo
kgf/arc min

itorque yokulinganisa
(kgf) ilahleke intshukumo
(i-arc min)

A1514.5±0.441arc min28

A2534±1.0210

A3565±1.9521

A45135±4.0545

A65250±7.5078

A75380±11.4110

Qaphela) i-arc min ithetha "i-engile" inxalenye.
       I-spring constant imele ixabiso eliphakathi (ixabiso elimele).

  (Umzekelo wokubalwa kwe-screw angle) phezulu

Ukusebenzisa i-A35 njengomzekelo, bala i-angle ye-screw xa i-torque isetyenziswe kwicala elinye.

  1) Xa i-torque yomthwalo i-1.5kgf*m (xa i-torque yomthwalo ikwindawo elahlekileyo yentshukumo) 
2) Kwimeko yomthwalo we-torque 60kgf * m

2) ukungcangcazela

Ukungcangcazela kuthetha ukungcangcazela [i-amplitude (mmp-p), i-acceleration (G)] kwidiski xa kufakwe umthwalo ongaphakathi kwidiski efakwe kwi-low-speed shaft kwaye ijikeleziswa yinjini.

  Umzobo 2 Ukungcangcazela kwezinyo flywheel vibration (isantya esisezantsi sokujikeleza)

(Iimeko zokulinganisa) 

  ifomu
umzuzu wecala lomthwalo we-inetia
irediyasi yokulinganisa
Ukuchaneka koMda weNdibanoFC-A35-59
1100kgf cm imizuzwana^2
550m
Jonga iSazobe 7, 8 kunye neTheyibhile 8

   phezulu

3) Impazamo yokuhanjiswa kwe-engile

Imposiso yothumelo lwe-engile ithetha umahluko phakathi kwe-angle yokujikelezisa imveliso yethiyori kunye neyona engile yokujikeleziswa kwemveliso xa ujikelezo olungenasizathu lufakwa.

Umzobo 3 ixabiso lemposiso yogqithiso lwe-engile

(Iimeko zokulinganisa) 

  ifomu
imeko yomthwalo
Ukuchaneka koMda weNdibanoFC-A35-59
akukho mthwalo
Jonga iSazobe 7, 8 kunye neTheyibhile 8

I-4) Akukho mthwalo wokuSebenza iTorque

Akukho mthwalo ohambayo we-torque uthetha i-torque ye-shaft yokufakwayo efunekayo ukujikeleza isinciphisi phantsi kwemeko yokungabikho komthwalo.

  Umzobo 4 Akukho mthwalo wexabiso letorque

Qaphela) 1. Umzobo 4 ubonisa ixabiso eliphakathi emva kokusebenza.
       2. Imiqathango yokulinganisa

  ubushushu betyala
Ukuchaneka komgangatho weNdibano
Isithambiso 30℃
Jonga iSazobe 7, 8 kunye neTheyibhile 8
igrisi

5) Yandisa i-torque yokuqala

Ukukhawuleza ukuqalisa i-torque kuthetha i-torque efunekayo ukuqalisa isinciphisi ukusuka kwicala lokuphuma kwimeko yokungabikho komthwalo.

  Itheyibhile 2 Ixabiso leTorque yokwandisa ukuqala

Imodeli eyongeza isantya sokuqalisa itorque(kgf)

A152.4

A255

A359

A4517

A6525

A7540

Qaphela) 1. Umzobo 4 ubonisa ixabiso eliphakathi emva kokusebenza.
       2. Imiqathango yokulinganisa

  ubushushu betyala
Ukuchaneka komgangatho weNdibano
Isithambiso 30℃
Jonga iSazobe 7, 8 kunye neTheyibhile 8
igrisi

6) Ukusebenza kakuhle

Umzobo 5 Igophe elisebenzayo 

Ukusebenza kuyahluka ngokuxhomekeke kwisantya sokujikeleza kwegalelo, itorque yomthwalo, ubushushu begrisi, kunye nokubilisa kwesantya.

Umzobo wesi-5 ubonisa amaxabiso asebenzayo esantya sokujikeleza xa ikhathalogu ikale itorque kunye nobushushu begrisi zizinzile.

Ukusebenza kuboniswa kumgca kunye nobubanzi obuthatha ukutshintshwa kwe-akhawunti ngenxa yenombolo yemodeli kunye nomlinganiselo wokunciphisa.

Umzobo 6 Umphezulu wegophe lolungelelwaniso olusebenzayo

Ixabiso loLungelo oluLungileyo = Ixabiso lokuSebenza (Umfanekiso 5) × IFactor yokuLungisa ngokuSebenzayo (Umfanekiso 6)

eyona)

1. Xa i-torque yomthwalo ingaphantsi kwe-torque elinganisiweyo, ixabiso lokuphumelela liyehla.Jonga umzobo 6 ukufumana ulungiso olufanelekileyo.

2. Ukuba i-torque ratio yi-1.0 okanye ngaphezulu, i-factor correct correction factor yi-1.0.

I-7) Umthwalo we-shaft we-high-speed-speed radial / thrust load

Xa i-gear okanye i-pulley ifakwe kwi-shaft-speed-speed shaft, isebenzise ngaphakathi kwinqanaba apho umthwalo we-radial kunye nomthwalo wokutyhala ungagqithisi amaxabiso avumelekileyo.
Jonga umthwalo we-radial kunye nomthwalo wokutyhala weshafti enesantya esiphezulu ngokweequation (1) ukuya ku-(3).

1.umthwalo weradial Ｐｒ

2. Umthwalo wethrustＰａ

3. Xa umthwalo weradial kunye nomthwalo wethrust usebenza kunye

Pr: umthwalo weradial [kgf]

Tl: itorque ikhutshelwe kwishafti yesantya esiphezulu sesinciphisi [kgf ]

R: I-Radius [m] ye-pitches ye-sprockets, i-gear, i-pulleys, njl.

Ipro: Umthwalo weradial ovumelekileyo [kgf] (Itheyibhile 3)

Pa: Umthwalo wethrust [kgf]

Pao: Umthwalo wokutyhala ovumelekileyo [kgf] (Itheyibhile 4)

Lf: Layisha i-coefficient yendawo (Itheyibhile 5)

Cf: i-coefficient yoqhagamshelo (Itheyibhile 6)

Fs1: Umlinganiso wempembelelo (Uluhlu 7)

Itheyibhile 3 Umthwalo ovumelekileyo weradial Pro(kgf) phezulu

Inombolo yegalelo lokujikeleza ngesantya sesantya se-rpm

4000300025002000175015001000750600

A15232526283031363942

A25343740434547545964

A35  5053576063727985

A45   626770738492100

A65     90951001141261335

A75      120126144159170

Itheyibhile 4 Umthwalo ovumelekileyo wokutyhala Pao(kgf) 

Inombolo yegalelo lokujikeleza ngesantya sesantya se-rpm

4000300025002000175015001000750600

A15252932353740485662

A25374246515559718290

A35  6166747884102111111

A45   103114122131131131131

A65     147147147147147147

A75      216232282323327

ITheyibhile 5 yeNdawo yokuLayisha iFactor Lf 

L
(mm) Inombolo yoMzekelo.

A15A25A35A45A65A75

100.90.86     

150.980.930.91    

2012.510.960.89  

251.561.251.090.94  

301.881.51.30.990.890.89

352.191.751.521.130.930.92

40  21.741.290.970.96

450   1.961.451.020.99

50   2.171.611.141.09

60     1.941.361.3

70      1.591.52

80      1.821.74

L (mm) xa Lf = 1 162023314446

  phezulu

Itheyibhile 6 inkalo yoQhagamshelo Cf Itheyibhile yesi-7 iFact factor Fs1

Indlela yoqhagamsheloCf

Ikhonkco1

izixhobo 1.25

Ibhanti lexesha1.25

Ibhanti le-V1.5

Umgangatho wempembeleloFs1

Xa kukho impembelelo encinci1

Kwimeko yomothuko omncinci 1-1.2

Kwimeko yomothuko omkhulu 1.4 ~ 1.6

8) Ukuchaneka komgangatho weNdibano

Umzobo we-7 indlela yeNdibano

● Uluhlu lwe-CYCLO reducer FA kufuneka zidityaniswe ngokusekelwe kwisikhokelo kwi-Figure 7 ABC.

● Ukuze ukwandise ukusebenza kwemveliso, nceda uyila kwaye uyivelise ngokubhekisele kwiThebhile 8 yeNdibano yeDimensional Precision.

Umzobo 8 umphezulu wokuchaneka komgangatho weNdibano

● Ngenxa yokuba uxinzelelo lusetyenziswe kwimeko, ububanzi bangaphakathi becala kufuneka bube ngaphantsi kwe-φa.

● Ubunzulu beflange yokuxhoma kufuneka ibe ngaphezulu kwe-b.

●Ukunqanda uphazamiseko phakathi kweflange ephumayo kunye nenxalenye yokunciphisa, idimensional yokunyuka phakathi kwecala kunye neflange exhomayo yi-M±C.

Ukuchaneka okucetyiswayo kwenxalenye yokunyuka kuboniswe kwiThebhile 8. Ifakwe ngaphakathi kwe-coaxiality kunye ne-parallelism

● Izikhokelo ezicetyiswayo zeendawo zokugxumeka ngu-d, e, kunye no-f kwiTheyibhuli yesi-8.

Uluhlu 8 (Iyunithi: mm) 

inombolo yemodeli a
ubuninzi b
umz k
Ubuncinane be-M±C kumbindi we-axis yokufakela yokujikeleza
i-coaxiality parallelism

defghij

A15905415.5±0.3φ115H7φ45H7φ85H7φ0.030φ0.030φ0.030φ0.025/87

A251156521±0.3φ145H7φ60H7φ110H7φ0.030φ0.030φ0.030φ0.035/112

A351446524±0.3φ180H7φ80H7φ135H7φ0.030φ0.030φ0.030φ0.040/137

A451828627±0.3φ220H7φ100H7φ170H7φ0.030φ0.030φ0.040φ0.050/172

A652268633±0.3φ270H7φ130H7φ210H7φ0.030φ0.030φ0.040φ0.065/212

A752628638±0.3φ310H7φ150H7φ235H7φ0.030φ0.030φ0.040φ0.070/237